+86-551-68661901
Home / News / Content

Aug 01, 2024

Main Parameters Of Thermistors

Main Parameters of Thermistors

 

Introduction to thermistors

Thermistors are a type of sensor resistors, and their typical feature is that their resistance value changes with temperature, that is, their resistance values ​​are different at different temperatures. According to different temperature coefficients, they are divided into:

1. Positive temperature coefficient thermistor (PTC thermistor, i.e. Positive Temperature Coefficient thermistor)

2. Negative temperature coefficient thermistor (NTC thermistor, i.e. Negative Temperature Coefficient thermistor)

Usually referred to as PTC and NTC. The higher the temperature, the greater the resistance value of PTC, and the lower the resistance value of NTC.

 

Main features

1. High sensitivity;

2. The working temperature range is studied. The commonly used temperature detection range is -55℃~315℃. The applicable temperature of high-temperature devices is higher than 315℃, and the applicable temperature of low-temperature devices is -273℃~-55℃;

3. Small size, can be placed on the surface, gaps and various cavities for temperature measurement;

4. Wide range of resistance values, large selection interval;

5. Strong plasticity, easy to process into various shapes and mass production;

6. Good stability and strong overload capacity.

 

Working principle

NTC thermistor

When the temperature is low, the resistance value is high; as the temperature rises, the resistance value decreases. The temperature coefficient range of NTC thermistor is -2%~-6.5%, which can be widely used in temperature measurement, temperature compensation, surge current suppression and other occasions.

PTC thermistor

At a certain critical temperature, the resistance will suddenly increase, mainly depending on the resistance change caused by the internal temperature change.

Once the temperature rises, it will cause a significant increase in resistance and enter the high resistance protection state. When the temperature drops, the resistance will decrease, and the resistance and temperature are positively correlated. Ratio. Often used in overvoltage, overcurrent, overload and other protection.

 

Technical parameters

1.Resistance

Resistance includes nominal resistance Rc and actual resistance RT

Nominal resistance Rc: generally refers to the actual resistance of the thermistor when the ambient temperature is 25°C. Nominal resistance is one of the key parameters of the thermistor, and the common resistance range is from 1KΩ to several hundred KΩ.

Actual resistance RT: the resistance value measured under certain temperature conditions.

2. Resistance tolerance (accuracy)

Like any resistor, standard resistors have tolerance (capacitance difference), usually with an accuracy of +1%, +5% and +10%.

3. Time constant T

Thermistor Thermistors have thermal inertia, and the time constant T is a parameter that describes the thermal inertia of thermistors.

Time constant T: When the ambient temperature (t1) changes to temperature (t2) without power consumption, the time required for the temperature change value to be 63.2% of the difference between t1-+2 (i.e. 1:1/e). The smaller r is, the smaller the thermal inertia of the thermistor is, that is, the faster the response time is, and the better the performance is.

4. Temperature coefficient αT

Resistance temperature coefficient αT: It indicates the rate of change of resistance when the temperature changes by 1°C, in units of %/°C.

5. Operating temperature range

This is the temperature range in which the thermistor is designed to operate.

Maximum operating temperature Tmax: The maximum temperature allowed for long-term continuous operation of the thermistor under specified technical conditions

6. Rated power PM

Rated power PM: Under specified technical conditions, the dissipated power allowed for long-term continuous load of the thermistor shall not exceed the rated power in actual use. If the ambient temperature of the thermistor exceeds 25°C, its load must be reduced accordingly.

7. Maximum voltage

For NTC thermistors, it is the maximum DC voltage that can be continuously applied to the thermistor without causing thermal runaway at a specified ambient temperature;

For PTC thermistors, the maximum DC voltage can be continuously applied to the thermistor and ensure normal operation in the PTC characteristic part at a specified ambient temperature and in still air.

Some additional parameter specifications may be used for professional thermistor applications, but these are some common main parameters.

8. Other parameters

1. B value (material constant)

Also known as the β value, this thermistor specification is a specific curve of the relationship between the resistance and temperature of the NTC thermistor. It is a parameter that describes the physical properties of the thermistor material and is also an indicator of thermal sensitivity. The larger the B value, the higher the sensitivity of the thermistor. It should be noted that in actual operation, the B value is not a constant, but increases slightly with the temperature increase.

2. B value/constant tolerance

As the name indicates, it is the allowable tolerance range for the B value.

3. Switching temperature tb

Switching temperature tb: The temperature at which the resistance value of the PTC thermistor begins to increase.

4. Maximum current (Int)

Maximum current (Int): refers to the maximum current allowed to pass through the PTC thermistor under the maximum operating voltage.

 

For any further queries, please feel free to contact: sales05@jingpusensor.com or whatapp: + 86 130 7205 5067

Send Message